ProSoft MVI56-PDPMV1 User Manual Download Page 14

Page: 14 / 251

Start Here

MVI56-PDPMV1 ♦ ControlLogix Platform

User Manual

PROFIBUS DPV1 Master

Page 14 of 251

ProSoft Technology, Inc.

1.5.1 Determining the Firmware Version of Your Processor

Important:

The RSLinx service must be installed and running on your computer in order for

RSLogix to communicate with the processor. Refer to your RSLinx and RSLogix documentation for

help configuring and troubleshooting these applications.

Connect an RS-232 serial cable from the COM (serial) port on your PC to the
communication port on the front of the processor.

Start RSLogix 5000 and close any existing project that may be loaded.

Open the

OMMUNICATIONS

menu and choose

NLINE

. RSLogix will

establish communication with the processor. This may take a few moments.

When RSLogix has established communication with the processor, the

Connected To Go Online

dialog box will open.

Summary of Contents for MVI56-PDPMV1




























































































































































































































































Search results

Summary of Contents for MVI56-PDPMV1

Reviews:

Related manuals for MVI56-PDPMV1

Brands by name

Popular brands

ProSoft MVI56-PDPMV1, User Manual

Search results

Summary of Contents for MVI56-PDPMV1

Reviews:

Related manuals for MVI56-PDPMV1

Brands by name

Popular brands