ProSoft MVI56-PDPMV1 User Manual Download Page 184

Page: 184 / 251

Diagnostics and Troubleshooting

MVI56-PDPMV1 ♦ ControlLogix Platform

User Manual

PROFIBUS DPV1 Master

Page 184 of 251

ProSoft Technology, Inc.

4.3.4 Using the Diagnostic Window in ProSoft Configuration Builder

To connect to the module’s Configuration/Debug serial port

Start

PCB

, and then right-click the module icon.

On the shortcut menu, choose

IAGNOSTICS

This action opens the

Diagnostics

dialog box.

Press

[?]

to open the

Main

menu.

Important:

The illustrations of configuration/debug menus in this section are intended as a general

guide, and may not exactly match the configuration/debug menus in your own module.

Summary of Contents for MVI56-PDPMV1




























































































































































































































































Search results

Summary of Contents for MVI56-PDPMV1

Reviews:

Related manuals for MVI56-PDPMV1

Brands by name

Popular brands

ProSoft MVI56-PDPMV1, User Manual

Search results

Summary of Contents for MVI56-PDPMV1

Reviews:

Related manuals for MVI56-PDPMV1

Brands by name

Popular brands