PRONAR NV161/1 Operator'S Manual Download Page 91

Page: 91 / 132

SECTION 5

Pronar NV161/1

│

NV161/2

│

NV161/3

│

NV161/4

│

NV161/5

5.7

DANGER

Before commencing work, the user must read the user manual for lifting jack and adhere
to the manufacturer's instructions.

The lifting jack must be stably supported on the ground and so must the axle.

Ensure that manure spreader shall not move during inspection of axle bearing slackness.

5.2.5 ADJUSTMENT OF SLACKNESS OF WHEEL AXLE BEARINGS

Preparation procedures

Prepare tractor and manure spreader for adjustment procedures according to

description provided in section 5.2.4.

Adjustment of slackness of axle bearings

Take off hub cover (1) – figure (5.3).

Take out split cotter pin (3) securing castellated nut (2).

Tighten castellated nut in order to eliminate slackness.

Wheel should rotate with insignificant resistance.

Undo nut (not less than 1/3 rotation) to align the nearest thread groove with

the opening in wheel axle pin. Wheel should rotate without excessive

resistance.

Nut must not be excessively tightened. Do not apply excessive

pressure because working conditions of the bearings may deteriorate.

Secure castellated nut with cotter pin and mount hub cap.

Delicately tap hub cap with rubber or wooden hammer.

Summary of Contents for NV161/1





































































































































Search results

Summary of Contents for NV161/1

Reviews:

Brands by name

Popular brands

PRONAR NV161/1, Operator'S Manual

Search results

Summary of Contents for NV161/1

Reviews:

Brands by name

Popular brands