PRONAR NV161/1 Operator'S Manual Download Page 100

Page: 100 / 132

Pronar NV161/1

│

NV161/2

│

NV161/3

│

NV161/4

│

NV161/5

SECTION 5

5.16

Adjustment of parking brake cable tension

Connect the manure spreader to tractor. Park manure spreader and tractor on

level surface.

Place securing chocks under one wheel of manure spreader.

Fully unscrew the bolt of the brake crank mechanism (1) – figure (5.7),

(anticlockwise).

Loosen nuts (6) on U-shaped clamps of steel cable

Tighten cable and tighten clamps.

Length of parking brake cables should be so selected that at total

release of working and parking brake the pulley block would be loose

and hanging by 1 - 2 cm compared to fully tensioned cables.

Replacing the parking brake cable

Connect the manure spreader to tractor. Park manure spreader and tractor on

level surface.

Place securing chocks under one wheel of manure spreader.

Fully unscrew the bolt of the brake crank mechanism (1).

Dismantle shackle (6) at the ends of the cable.

Unlock pin and guide roller of pulley block (4).

Unlock and dismount pins in pulley block (4) and in brake crank

mechanism (1).

Loosen the nuts (6) of U-shaped clamps (5).

If necessary, dismount guide rollers (3).

Dismantle cable.

Clean parking brake components, lubricate crank mechanism and pins of

cable guide rollers (3).

Install new cable.

After the first loading of cable, re-check the condition of cable ends, correct if

necessary.

Summary of Contents for NV161/1





































































































































Search results

Summary of Contents for NV161/1

Reviews:

Brands by name

Popular brands

PRONAR NV161/1, Operator'S Manual

Search results

Summary of Contents for NV161/1

Reviews:

Brands by name

Popular brands