PRONAR NV161/1 Operator'S Manual Download Page 50

Page: 50 / 132

Pronar NV161/1

│

NV161/2

│

NV161/3

│

NV161/4

│

NV161/5

SECTION 3

3.6

The chain tension is adjusted with tensioning bolts (8). The principle of conveyor speed

adjustment is described in section 4.5.1 – figure (4.2), whereas the method of adjusting the

tension of floor conveyor chains is described in section 5.7.

FIGURE 3.2

Feeding mechanism NV161/1, NV161/2, NV161/3

(1) transfer unit, (2) tensioning unit, (3) drive unit, (4) chain, (5) scraping strip, (6) hydraulic

motor, (7) reduction gear, (8) tensioning bolt

ATTENTION

Movement direction of loaded feeding mechanism may be reversed only for a short
time.

The feeding mechanism may be started only if the manure spreader's slide gate is
raised (if it is included in the manure spreader's equipment). Otherwise, the manure
spreader may be seriously damaged.

Summary of Contents for NV161/1





































































































































Search results

Summary of Contents for NV161/1

Reviews:

Brands by name

Popular brands

PRONAR NV161/1, Operator'S Manual

Search results

Summary of Contents for NV161/1

Reviews:

Brands by name

Popular brands