PRONAR NV161/1 Operator'S Manual Download Page 107

Page: 107 / 132

SECTION 5

Pronar NV161/1

│

NV161/2

│

NV161/3

│

NV161/4

│

NV161/5

5.23

Released valve stem should automatically close and stop flow of air from the

tank.

If the valve stem resists returning to its position, then the whole drain

valve must be unscrewed and cleaned or replaced (if it is damaged) -

see section 5.3.5.

5.3.5 CLEANING THE DRAIN VALVE

DANGER

Release air from the air tank before dismantling drain valve.

Required maintenance activities:

Reduce pressure in air tank.

Reduction of pressure in tank is achieved by tilting the drain valve

stem.

Unscrew valve.

Clean valve, blow with compressed air.

Change copper seal.

Screw in valve, fill tank with air and check tank tightness.

Cleaning valve:

•

every 12 months (before winter period).

5.3.6 CLEANING AND MAINTAINING PNEUMATIC CONDUIT CONNECTIONS

AND PNEUMATIC SOCKETS

DANGER

Unreliable and dirty manure spreader connections may cause unreliability and faulty
functioning of braking system.

Summary of Contents for NV161/1





































































































































Search results

Summary of Contents for NV161/1

Reviews:

Brands by name

Popular brands

PRONAR NV161/1, Operator'S Manual

Search results

Summary of Contents for NV161/1

Reviews:

Brands by name

Popular brands