manualshive.com logo in svg

Polaris RZR PRO R, Service Manual

Share
Download
Polaris RZR PRO R Service Manual Download Page 489

12

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

© Copyright Polaris Industries Inc.

12.31

5. Remove one fastener

t

, three push-pins

y

, and

remove the front fender. Repeat for opposite side of
the vehicle. If equipped, disconnect antenna.

6. Remove two fasteners

u

and remove the fender

mounting bracket.

7. Remove four fasteners

i

and remove the front

bumper assembly.

8. Disconnect electrical connectors from the headlights

and accent lights, if equipped..

9. Remove two push-pins

o

and remove the front

fascia.

10. Disconnect coolant hoses from the radiator.

11. Disconnect electrical connector from cooling fan

assembly.

12. Remove two fasteners

a

retaining the radiator

assembly.

13. Disconnect any wiring from the radiator assembly.

14. Remove radiator, cooling fan and radiator shroud as

an assembly.

15. Remove push-pins to separate radiator from fan and

shroud assemblies.

INSTALLATION

1. Install new radiator onto cooling fan and shroud, and

install assembly mounting push-pins.

2. Mount radiator assembly onto vehicle chassis and

install radiator hoses.

3. Route and install wiring harness onto radiator

assembly.

ELECTRICAL

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands