Polaris RZR PRO R Service Manual Download Page 254

Page: 254 / 508

6.4

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

DRIVE BELT

BELT REMOVAL

1. Park vehicle on a level surface.

2. Remove seats. On 4-seat models, remove the rear

seats.

3. Remove upper and lower rear close-off panels.

4. Loosen hose clamp

and remove the PVT intake

hose.

5. Remove five fasteners

, disengage remaining 1/4

turn latches, and remove the outer PVT cover.

6. Remove the drive belt.

BELT INSPECTION

1. Inspect belt for hour glassing (extreme circular wear

in at least one spot and on both sides of the belt).
Hour glassing occurs when the drive train does not
move and the drive clutch engages the belt.

2. Inspect belt for loose cords, missing cogs, cracks,

abrasions, thin spots, or excessive wear. Compare
belt measurements with a new drive belt. Replace if
necessary.

3. Belts with thin spots, burn marks, etc., should be

replaced to eliminate noise, vibration, or erratic PVT
operation. See the Troubleshooting Chart at the end
of this chapter for possible causes.

PVT SYSTEM

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR PRO R

Reviews:

Related manuals for RZR PRO R

Brands by name

Popular brands

Polaris RZR PRO R, Service Manual

Search results

Summary of Contents for RZR PRO R

Reviews:

Related manuals for RZR PRO R

Brands by name

Popular brands