Polaris RZR PRO R Service Manual Download Page 355

Page: 355 / 508

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

9.17

4. Properly support the suspension using a floor jack or

tie down strap to prevent suspension from fully
drooping.

CAUTION

Suspension must be supported when the shock

absorber is removed. If suspension is not properly

supported, suspension weight will rest on the inner tie

rod, which may result in damage to the tie rod and/or tie

rod boot.

Suspension/knuckle should be supported using a floor

jack, or securely strapped to a vehicle tie-down point on

the chassis.

5. Remove lower shock fastener

and lower stabilizer

bar link fastener

6. Remove and discard ball joint nut

. Remove two

control arm mounting fasteners

7. Remove lower control arm.

INSTALLATION

1. Loosely install lower control arm, mounting fasteners,

and NEW ball joint nut into place.

2. Install lower shock and stabilizer bar link fasteners

into the control arm.

3. Torque Fasteners to specification.

TORQUE

Control Arm Mounting Fasteners:

133 ft-lbs (180 Nm) - Torque bolt side

TORQUE

Lower Ball Joint Fastener:

44 ft-lbs (60 Nm) + 90° (Single Use)

TORQUE

Shock Mounting Fastener:

133 ft-lbs (180 Nm) - Torque bolt side

TORQUE

Stabilizer Bar Link Fastener:

81 ft-lbs (110 Nm)

STEERING / SUSPENSION

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR PRO R

Reviews:

Related manuals for RZR PRO R

Brands by name

Popular brands

Polaris RZR PRO R, Service Manual

Search results

Summary of Contents for RZR PRO R

Reviews:

Related manuals for RZR PRO R

Brands by name

Popular brands