Polaris RZR PRO R Service Manual Download Page 127

Page: 127 / 508

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

3.13

AIR BOX REMOVAL

1. Remove seats.

2. Remove upper rear close off panel.

3. Remove eight fasteners

and two push rivets

Remove close-off panel cover.

4. Loosen the band clamps

retaining the intake hoses

to the air box.

5. Remove two fasteners

retaining the air box.

6. Lift air box upward to disengage lower mounting tabs

and remove air box from vehicle.

AIR BOX INSTALLATION

1. Install the air box and re-engage lower mounting tabs.

2. Install the intake hoses onto the air box. Tighten hose

clamps to specification.

TORQUE

Intake Hose Clamps:

35 in-lbs (3 Nm)

3. Install two air box mounting fasteners. Torque

fasteners to specification.

TORQUE

Air Box Mounting Fasteners:

9 ft-lbs (12 Nm)

4. Install rear close off panel cover. Torque fasteners to

specification.

TORQUE

Rear Close Off Panel Cover Fasteners:

7 ft-lbs (10 Nm)

5. Install upper rear close off panel.

6. Install both seats.

ENGINE / COOLING SYSTEM

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR PRO R

Reviews:

Brands by name

Popular brands

Polaris RZR PRO R, Service Manual

Search results

Summary of Contents for RZR PRO R

Reviews:

Brands by name

Popular brands