Polaris RZR PRO R Service Manual Download Page 334

Page: 334 / 508

8.34

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

FRONT GEARCASE ASSEMBLY

1. Clean surface between housing and pinion assembly.

2. Apply a thin bead of gasket sealant

(3233885)

around

the pinion-to-case sealing surface

3. Install pinion gear, housing, and solenoid as an

assembly. Torque fasteners to specification.

TORQUE

Pinion Gear Housing Fasteners:

7 ft-lbs (10 Nm) – Apply Loctite 2760

4. Install ring gear assembly. Torque fasteners to

specification.

TORQUE

Ring Gear Assembly Fasteners:

14 ft-lbs (19 Nm) + 40°

If replaced

Install shim, engagement dog, and shift

arm onto cover plate. Torque fasteners to
specification.

TORQUE

Shift Arm Fasteners:

50 in-lbs (6 Nm)

6. Install cover plate. Torque fasteners to specification.

IMPORTANT

Apply silicone assembly grease to the cover o-ring and

the axle seal ID.

Line up the differential engagement dogs with the ring

gear slots to install the cover plate. Once aligned, rock

the cover plate down into place. Do NOT use a hammer

on the cover plate.

TORQUE

Cover Plate Fasteners:

23 ft-lbs (31 Nm)

FINAL DRIVE

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR PRO R

Reviews:

Brands by name

Popular brands

Polaris RZR PRO R, Service Manual

Search results

Summary of Contents for RZR PRO R

Reviews:

Brands by name

Popular brands