Polaris RZR PRO R Service Manual Download Page 223

Page: 223 / 508

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

4.11

PPS REPLACEMENT

NOTICE

The PPS is calibrated to the throttle pedal. If the PPS is

faulty, the throttle pedal assembly must be replaced.

1. Remove the drivers seat and disconnect the negative

(-) battery cable.

2. Disconnect the PPS harness connection located on

the throttle pedal.

3. Remove the three fasteners

retaining the throttle

pedal assembly to the frame.

4. Remove pedal assembly.

5. Reverse procedure for installation. Torque fasteners

to specification.

TORQUE

PPS Mounting Fasteners:

18 ft-lbs (24 Nm)

Battery Cable Fasteners:

60 in-lbs (9 Nm)

OXYGEN SENSOR

OXYGEN SENSOR INFORMATION

The oxygen sensor, located on the exhaust pipe before
the muffler, uses a 4 wire heated element.

2018

CONNECTOR

PIN

WIRE

COLOR

PIN AND WIRE

CONNECTION

Purple

Heater Power

White

Heater Ground

Gray

Sensor Output

Black

Sensor Ground

ENGINE ELECTRICAL

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR PRO R

Reviews:

Related manuals for RZR PRO R

Brands by name

Popular brands

Polaris RZR PRO R, Service Manual

Search results

Summary of Contents for RZR PRO R

Reviews:

Related manuals for RZR PRO R

Brands by name

Popular brands