manualshive.com logo in svg

Polaris RZR PRO R, Service Manual

The Polaris RZR PRO R is a high-performance side-by-side vehicle designed for off-road enthusiasts. For maintenance and repair needs, download the free Service Manual from manualshive.com. This comprehensive manual includes detailed instructions and diagrams to help keep your RZR PRO R running smoothly and efficiently.

Share
Download
background image

6.20

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

© Copyright Polaris Industries Inc.

DRIVEN CLUTCH SERVICE

DRIVEN CLUTCH REMOVAL

1. Park vehicle on a level surface.

2. Remove seats. On 4-seat models, remove the rear

seats.

3. Remove upper and lower rear close-off panels.

4. Loosen hose clamp

w

and remove the PVT intake

hose.

5. Remove five fasteners

e

, disengage remaining 1/4

turn latches, and remove the outer PVT cover.

6. Remove the drive belt.

7. Remove bolt

r

, spacer

t

, and washer

y

. Remove

the driven clutch.

PVT SYSTEM

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RZR PRO R

Honda Pioneer SXS500M 2018 Owner'S Manual preview
Pioneer SXS500M 2018
Brand: Honda Pages: 268
Aeon COBRA 50 2007 Service Manual preview
COBRA 50 2007
Brand: Aeon Pages: 126
Hisun HS 200UTV-2 Owner'S Manual preview
HS 200UTV-2
Brand: Hisun Pages: 57
Honda 1997 TRX300 Fourtrax 300 Owner'S Manual preview
1997 TRX300 Fourtrax 300
Brand: Honda Pages: 162
Clam POLAR TRAILER HD MAX 10535 Quick Start Manual preview
POLAR TRAILER HD MAX 10535
Brand: Clam Pages: 12
Monowalker fatmate User Manual preview
fatmate
Brand: Monowalker Pages: 27
Yamaha YFM350 Warrior Instruction Supplement preview
YFM350 Warrior
Brand: Yamaha Pages: 3
Yamaha YFM660F 2002 Assembly Manual preview
YFM660F 2002
Brand: Yamaha Pages: 44
Yamaha YFM400FAR Assembly Manual preview
YFM400FAR
Brand: Yamaha Pages: 32
Yamaha YFM350S 2003 Assembly Manual preview
YFM350S 2003
Brand: Yamaha Pages: 42
Yamaha YFM250BT 2004 Supplementary Service Manual preview
YFM250BT 2004
Brand: Yamaha Pages: 34
Yamaha YFM450FAT Supplementary Service Manual preview
YFM450FAT
Brand: Yamaha Pages: 73
Yamaha WOLVERINE YFM35XV Assembly Manual preview
WOLVERINE YFM35XV
Brand: Yamaha Pages: 34
Yamaha YFM350R-W Supplementary Service Manual preview
YFM350R-W
Brand: Yamaha Pages: 72
Yamaha YFM50RY Owner'S Manual preview
YFM50RY
Brand: Yamaha Pages: 116
Yamaha YFM50R Owner'S Manual preview
YFM50R
Brand: Yamaha Pages: 116
Yamaha YFM35RW Owner'S Manual preview
YFM35RW
Brand: Yamaha Pages: 134
Yamaha YFM350FAS Supplementary Service Manual preview
YFM350FAS
Brand: Yamaha Pages: 119

Brands by name

Popular brands

Load more brands