manualshive.com logo in svg

Polaris RZR PRO R, Service Manual

Share
Download
Polaris RZR PRO R Service Manual Download Page 159

3

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

© Copyright Polaris Industries Inc.

3.45

7. Remove and retain camshaft gaskets.

8. Remove the camshaft carriers.

9. Remove the intake and exhaust camshaft.

CAMSHAFT CLEANING AND
INSPECTION

• Inspect the camshaft journals and lobes for wear or

scoring.

• Inspect the camshaft sprocket alignment notch for

damage.

• Inspect the camshaft cover for damage or loose oil

control baffles.

• Clean the camshaft cover.

• Wash the camshaft in solvent.

• Oil the camshaft.

• Inspect the camshaft cover for cracks or other signs of

damage.

ENGINE / COOLING SYSTEM

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands