Polaris RZR PRO R Service Manual Download Page 184

Page: 184 / 508

3.70

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

ENGINE ASSEMBLY - BOTTOM END

OIL PAN CLEANING AND INSPECTION

1. Clean the oil pan mating surface.

2. Clean the oil pan. Remove all the sludge and the oil

deposits.

3. Inspect the threads for the engine oil drain plug.

4. Inspect the oil pan for cracking near the pan rail and

the transmission mounting points.

5. Repair or replace the oil pan as necessary.

OIL PUMP ASSEMBLY

IMPORTANT

Lubricate seals with oil before installation or seal

damage may occur.

1. Install the pickup tube, oil tube, and seals to the oil

pump. Torque fastener to specification.

TORQUE

Oil Pump Pickup Fasteners:

80 in-lbs (9 N·m)

2. Install the regulator valve

into the oil pan. Torque to

specification

TORQUE

Regulator Valve Assembly:

21 ft-lbs (28 N·m)

ENGINE / COOLING SYSTEM

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR PRO R

Reviews:

Related manuals for RZR PRO R

Brands by name

Popular brands

Polaris RZR PRO R, Service Manual

Search results

Summary of Contents for RZR PRO R

Reviews:

Related manuals for RZR PRO R

Brands by name

Popular brands