Polaris RZR PRO R Service Manual Download Page 132

Page: 132 / 508

3.18

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

COOLING SYSTEM SPECIFICATIONS

COOLING SYSTEM CAPACITY

RZR

PRO R

10.4 qt (9.8 L)

RZR

PRO R4

12.4 qt (11.7 L)

TEMPERATURE SPECIFICATIONS

CONDITION

COOLANT TEMP

° F (° C)

Room Temperature

68° F (20° C)

Thermostat Begins Opening

180° F (82° C)

Fan Off

(when temp decreases

to)

190° F (88° C)

Fan On (fan speed 50%)

(engine running) (when temp

increases to)

190° F (88° C)

Fan On (fan speed 100%)

(engine running) (when temp

increases to)

207° F (97° C)

Thermostat Full Open

203° F (95° C)

Fan On

(engine OFF)

* fan will run up to 30 seconds

without engine running

230° F (110° C)

Engine Temperature

Overheat

Indicator ON

241° F (116° C)

Engine Protection

Torque

Limit

244° F (118° C)

Engine Protection

Cylinder

Deactivation

250° F (121° C)

Engine Protection

Shutdown

& Overheat Indicator Flashes

255° F (124° C)

COOLING SYSTEM PRESSURE TEST

1. Remove the coolant bottle cover.

2. Remove pressure cap

and pressure test the cap

using a commercially available pressure tester. The
pressure cap relief pressure is 18 psi. Replace the
cap if it does not meet this specification.

WARNING

Never remove pressure cap when engine is warm or

hot. The cooling system is under pressure and serious

burns may result. Allow the engine to cool before

servicing.

3. To test the cooling system, connect the pressure

tester to the cooling neck

with the correct adapter.

4. The system must maintain 10 psi for five minutes or

longer. If pressure loss is evident within five minutes,
check the filler neck, radiator, hoses, clamps and
water pump weep hole for leakage.

ENGINE / COOLING SYSTEM

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Search results

Summary of Contents for RZR PRO R

Reviews:

Related manuals for RZR PRO R

Brands by name

Popular brands

Polaris RZR PRO R, Service Manual

Search results

Summary of Contents for RZR PRO R

Reviews:

Related manuals for RZR PRO R

Brands by name

Popular brands