manualshive.com logo in svg

Polaris RZR PRO R, Service Manual

Share
Download
Polaris RZR PRO R Service Manual Download Page 133

3

9940259 R02 - 2022

RZR

PRO R / PRO R 4 Service Manual

© Copyright Polaris Industries Inc.

3.19

RADIATOR REPLACEMENT

REMOVAL

1. Drain cooling system.

2. Remove two fasteners

q

and remove the hood.

3. Remove one fastener

w

and remove the nose cone.

4. Remove thirteen fasteners

e

, one push-pin

r

, and

remove the front fender flare. Repeat for opposite
side of the vehicle.

5. Remove one fastener

t

, three push-pins

y

, and

remove the front fender. Repeat for opposite side of
the vehicle. If equipped, disconnect antenna.

6. Remove two fasteners

u

and remove the fender

mounting bracket.

7. Remove four fasteners

i

and remove the front

bumper assembly.

8. Disconnect electrical connectors from the headlights

and accent lights, if equipped..

ENGINE / COOLING SYSTEM

Summary of Contents for RZR PRO R





























































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands