Phoenix Contact Axioline F User Manual Download Page 85

Page: 85 / 86

Appendix: revision history

105739_en_04

PHOENIX CONTACT

E Appendix:

revision

history

Revision

Date

Contents

01/2014

First publication

02/2014

Revision HW/FW 00/101 extended

“Color code of function” replaced by “Function identification”

“Boost U

” replaced by “Supply voltage U

”

Images for assembly and removal updated

Description for supply voltages under 4.2.2 “Electrical installation of the module” revised

E LED deleted from table

“Axioline” replaced by “Axioline F”

“BK module” replaced by “Bus coupler”

“Device bus” replaced by “Local bus”

Editorial corrections

global

08/2014

Editorial corrections (page numbers, formats, hyperlinks)

Drawing correction for Figure 3-1

Specifications for acknowledging errors 0x2370, 0x2371, 0x8F08, 0x8F09, and 0x2380

in Table 8-9 “Safe digital output errors” modified

Ambient temperature according to CUL

added

Current consumption from UBUS updated

Current consumption from UO updated

Maximum output current per output (channel) updated

Maximum output current of all outputs (total current) updated

Maximum output current per group (total current) updated

global

11/2016

Order number for user manual removed

HW/FW revision updated

Figure 2-3 “Local diagnostics and status indicators” revised

Table 2-1 “Overview of diagnostics LEDs” revised

Note on “Operating time in the error state” revised

Section 3, “Integration of the Axioline F local bus” / Section 3.1, “Supply voltage of the

module logic” revised

Figure 4-1 “DIP switch” and “Overview of the switch positions” revised

Section 7.1.1, “Startup mode” inserted

Description for “Error location” in Section 8, “Errors: messages and removal” extended

Error message “ 0x03FB” in Section 8.2.3, “Parameterization errors” extended

Error message “0xA012” in Section 8.2.4, “General errors” extended (previously

“0x5010”)

Ambient temperature operation according to CUL

removed

UL note regarding connection data inserted

Additional text for maximum output currents according to CUL

revised

Section 10.4, “Ordering data and download data” revised / Section 10.4.3, “Download

data: software” extended

“F_Destination_Address” in Section B 2, “i-Parameters” deleted, “PST_Device_ID”

extended

Cover

Summary of Contents for Axioline F























































































Search results

Summary of Contents for Axioline F

Reviews:

Phoenix Contact Axioline F, User Manual, Page: 85 / 86

Search results

Summary of Contents for Axioline F

Reviews: