Phoenix Contact Axioline F User Manual Download Page 17

Page: 17 / 86

Product description

105739_en_04

PHOENIX CONTACT

2.6

Local diagnostics and status indicators

Figure 2-3

Local diagnostics and status indicators

Table 2-1

Overview of diagnostics LEDs

D
Uo

Designation

Color

State

Description

Red/yellow/

green

Diagnostics for local bus communication

Green on

The device is ready for operation, communication within the station is OK.

All data is valid. There is no error.

Flashing green

The device is ready for operation, communication within the station is OK.

The data is

not

valid. Valid data from the controller/higher-level network not

available.

There is no error on the module.

Flashing

green/yellow

The device is ready for operation, communication within the station is OK.

Output data

cannot

be output and/or input data

cannot

be read.

There is an error on the I/O side of the module.

Yellow on

The device is ready for operation, but has still not detected a valid cycle

after power on.

Flashing

yellow

The device is not (yet) part of the active configuration.

Red on

The device is ready for operation, but has lost the connection to the bus

head.

Flashing red

The device is ready for operation, but there is no connection to the previous

device.

Off

Device is in (power) reset.

Green

Diagnostics for digital output supply

Green on

Supply for the digital outputs is present and is > around 17 V DC.

Flashing green

Supply for the digital outputs is not present or is < around 17 V DC.

Red

Diagnostics for failure state

Off

The safety application has a valid parameterization.

(Only applies if UO is on or flashing at the same time.)

Red on

Hardware fault. Communication to the higher-level controller is disabled.

The module has entered the safe state (failure state).

Flashing red

The module is not parameterized.

Summary of Contents for Axioline F























































































Search results

Summary of Contents for Axioline F

Reviews:

Phoenix Contact Axioline F, User Manual, Page: 17 / 86

Search results

Summary of Contents for Axioline F

Reviews: