manualshive.com logo in svg

Phoenix Contact Axioline F, User Manual, Page: 70 / 86

Share
Download
Phoenix Contact Axioline F User Manual Download Page 70

AXL F PSDO8/3 1F

70

PHOENIX CONTACT

105739_en_04

10.4

Ordering data and download data

10.4.1

Ordering data: module

10.4.2

Download data: documentation

10.4.3

Download data: software

Description

Type

Order No.

Pcs./Pkt.

Axioline F module with safe digital outputs

AXL F PSDO8/3 1F

2701560

1

Make sure you always use the latest documentation. It can be found in the download area for the specified product 

at 

phoenixcontact.net/products

.

Description

Type

Download area for Order 

No.

Axioline F

User manual

Axioline F: system and installation

UM EN AXL F SYS INST

2701560

User manual

Axioline F: diagnostic registers and error messages

UM EN AXL F SYS DIAG

2701560

PROFIsafe

Specification

PROFIsafe - Profile for Safety Technology on PROFIBUS DP and 

PROFINET IO, Version 2.4, February 2007

See 

profisafe.net

Documentation for PROFIsafe, PROFIBUS, and PROFINET is available on the Internet at

profibus.com/download/

.

Make sure you always use the latest software. The software can be downloaded free of charge at 

phoenixcontact.net/products

.

Description

Type

Download area for Order 

No.

Software for starting up and parameterizing Axioline stations

2700636

Summary of Contents for Axioline F























































































Reviews:

No comments