manualshive.com logo in svg

Phoenix Contact Axioline F, User Manual, Page: 9 / 86

Share
Download
Phoenix Contact Axioline F User Manual Download Page 9

For your safety

105739_en_04

PHOENIX CONTACT

9

1

For  your  safety

Purpose of this user manual

This user manual provides information about how the module works, its operating and 

connection elements, and its parameter settings.

Validity of the user manual

This user manual is valid for the AXL F PSDO8/3 1F module in the version indicated on the 

inner cover page, as well as for the same or later versions if replaced with devices of the 

same type.

1.1

General safety notes

Qualified personnel

In terms of this user manual, qualified personnel are persons who, because of their 

education, experience and instruction, and their knowledge of relevant standards, 

regulations, accident prevention, and service conditions, have been authorized to carry out 

any required operations, and who are able to recognize and avoid any possible dangers.

Furthermore, knowledge of the following topics and products is required:

–

Non-safety-related target system (e.g., PROFIBUS, PROFINET)

–

PROFIsafe

–

Components  used

–

Axioline F product range

–

Operation of the software tools

–

Safety regulations in the field of application

In the context of the use of the PROFIsafe system, the following operations must only be 

carried out by qualified personnel:

–

Planning

–

Configuration, parameterization, programming

–

Installation, startup, servicing

–

Maintenance, decommissioning

Documentation

Observe all information in this user manual and the accompanying documents: see 

Section 1.6 “Documentation” on page 12.

Safety of personnel and 

equipment

The safety of personnel and equipment can only be assured if the module is used correctly: 

see Section 1.5 “Intended use” on page 11.

Error detection

Depending on the wiring and the parameterization, the module detects errors within the 

safety equipment.

WARNING: Risk of injury

Depending on the application, inappropriate use of the module may result in serious injury.

•

Observe all the safety notes and warning instructions provided in this section and 

elsewhere in this user manual.

Summary of Contents for Axioline F























































































Reviews:

No comments