manualshive.com logo in svg

Phoenix Contact Axioline F, User Manual, Page: 60 / 86

Share
Download
Phoenix Contact Axioline F User Manual Download Page 60

AXL F PSDO8/3 1F

60

PHOENIX CONTACT

105739_en_04

8.2.4

General errors

Table 8-12

General errors

AXIO code

Error cause

LED

Description/effect

Acknowledgment/remedy

0x4210

Critical module 

temperature

SD on The module temperature has 

reached a critical value. Immediate 

shutdown. A further temperature 

increase causes the device firmware 

to switch the module to the safe 

state.

Check ambient conditions and 

switching frequency and adjust, if 

necessary.

This diagnostic message can be 

acknowledged. Acknowledgment 

deletes the diagnostic message.

0xA012

Hardware fault or 

application on the module 

is not ready

FS on Communication to the higher-level 

safe controller is disabled. The 

module switches to the safe state.

Perform power up.

If an error message is output again, 

the module is faulty and must be 

replaced.

DIP switch moved during 

operation

FS on The module switches to the safe 

state.

Check DIP switch position.

Perform power up.

This diagnostic message cannot be 

acknowledged.

Summary of Contents for Axioline F























































































Reviews:

No comments