Panasonic KX-UT670 Administrator'S Manual Download Page 10

Page: 10 / 250

RINGING_OFF_SETTING_ENABLE ........................................................................163

AUTO_CALL_HOLD ..................................................................................................163

REDIALKEY_CALLLOG_ENABLE ............................................................................164

ONHOOK_TRANSFER_ENABLE .............................................................................164

DISCONNECTION_MODE ........................................................................................164

TONE_LEN_DISCONNECT_HANDSET ...................................................................164

TONE_LEN_DISCONNECT_HANDSFREE ..............................................................165

KEY_PAD_TONE ......................................................................................................165

DDI_ICD_GROUP_DISPLAY ....................................................................................165

5.6.2

Tone Settings ...............................................................................................................166

DIAL_TONE1_FRQ ...................................................................................................166

DIAL_TONE1_GAIN ..................................................................................................166

DIAL_TONE1_TIMING ..............................................................................................166

DIAL_TONE2_FRQ ...................................................................................................166

DIAL_TONE2_GAIN ..................................................................................................167

DIAL_TONE2_TIMING ..............................................................................................167

DIAL_TONE4_FRQ ...................................................................................................167

DIAL_TONE4_GAIN ..................................................................................................167

DIAL_TONE4_TIMING ..............................................................................................167

BUSY_TONE_FRQ ...................................................................................................168

BUSY_TONE_GAIN ..................................................................................................168

BUSY_TONE_TIMING ..............................................................................................168

REORDER_TONE_FRQ ...........................................................................................169

REORDER_TONE_GAIN ..........................................................................................169

REORDER_TONE_TIMING ......................................................................................169

RINGBACK_TONE_FRQ ..........................................................................................169

RINGBACK_TONE_GAIN .........................................................................................170

RINGBACK_TONE_TIMING .....................................................................................170

HOLD_ALARM_FRQ .................................................................................................170

HOLD_ALARM_GAIN ...............................................................................................170

HOLD_ALARM_TIMING ............................................................................................170

CW_TONE1_FRQ .....................................................................................................171

CW_TONE1_GAIN ....................................................................................................171

CW_TONE1_TIMING ................................................................................................171

HOLD_TONE_FRQ ...................................................................................................171

HOLD_TONE_GAIN ..................................................................................................171

HOLD_TONE_TIMING ..............................................................................................172

5.6.3

Telephone Settings ......................................................................................................172

DISPLAY_NAME_REPLACE ....................................................................................172

NUMBER_MATCHING_LOWER_DIGIT ...................................................................172

NUMBER_MATCHING_UPPER_DIGIT ....................................................................172

DISPLAY_DATE_PATTERN .....................................................................................173

DISPLAY_TIME_PATTERN ......................................................................................173

DEFAULT_LANGUAGE ............................................................................................173

POUND_KEY_DELIMITER_ENABLE .......................................................................174

WALLPAPER_URI_HOME ........................................................................................174

WALLPAPER_URI_PHONE ......................................................................................174

LOGO_URI_PHONE .................................................................................................175

5.6.4

Flexible Button Settings ................................................................................................175

FLEX_BUTTON_FACILITY_ACTx ............................................................................175

FLEX_BUTTON_FACILITY_ARGx ...........................................................................175

FLEX_BUTTON_LABELx ..........................................................................................176

5.7

VoIP Settings .................................................................................................................176

5.7.1

Codec Settings .............................................................................................................176

CODEC_G711_REQ .................................................................................................176

Administrator Guide

Document Version 2012-07

Table of Contents

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands