Panasonic KX-UT670 Administrator'S Manual Download Page 97

Page: 97 / 250

Supports Rport (RFC 3581)

Description

Selects whether to add the "rport" parameter to the top Via header field
value of requests generated. For details, refer to RFC 3581.

Value Range

•

Yes

•

Default Value

Configuration File Reference

SIP_ADD_RPORT_n (Page 201)

4.6.2.13 Security

Enable SSAF (SIP Source Address Filter)

Description

Selects whether to enable SSAF (SIP Source Address Filter) for the
SIP servers (registrar server, proxy server, and presence server).

Value Range

•

Yes

•

Note

•

If you select

[Yes]

, the unit receives SIP messages only from

the source addresses stored in the SIP servers (registrar
server, proxy server, and presence server), and not from other
addresses. However, if

[Outbound Proxy Server Address]

4.6.2.3 Outbound Proxy Server

is specified, the unit also

receives SIP messages from the source address stored in the
SIP outbound proxy server.

Default Value

Configuration File Reference

SIP_DETECT_SSAF_n (Page 206)

Document Version 2012-07

Administrator Guide

Section 4 Web User Interface Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands