Panasonic KX-UT670 Administrator'S Manual Download Page 72

Page: 72 / 250

Subnet Mask

Description

Specifies the subnet mask for the unit.

Note

•

This setting is available only when

[Connection Mode]

is set

[Static]

Value Range

Max. 15 characters

Default Value

Not stored.

Phone User Interface
Reference

Network Settings (Page 16)

Default Gateway

Description

Specifies the IP address of the default gateway for the network where
the unit is connected.

Note

•

This setting is available only when

[Connection Mode]

is set

[Static]

Value Range

Max. 15 characters

Default Value

Not stored.

Phone User Interface
Reference

Network Settings (Page 16)

DNS1

Description

Specifies the IP address of the primary DNS server.

Note

•

This setting is available only when

[Connection Mode]

is set

[Static]

Value Range

Max. 15 characters

Default Value

Not stored.

Phone User Interface
Reference

Network Settings (Page 16)

DNS2

Description

Specifies the IP address of the secondary DNS server.

Note

•

This setting is available only when

[Connection Mode]

is set

[Static]

Administrator Guide

Document Version 2012-07

Section 4 Web User Interface Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands