Panasonic KX-UT670 Administrator'S Manual Download Page 220 | Manualshive

Page: 220 / 250

background image

7.1 General Information on Firmware Update

You can update the unit’s firmware to improve the unit’s operation. You can configure the unit so that it
automatically downloads the new firmware file from a specified location. The firmware update will be executed
when the unit is restarted.

Configuration
file

Provisioning server

Firmware server

A

C

B

Firmware

A

Download configuration file

B

Check for update by comparing the unit’s firmware version with the downloaded configuration file’s version

C

Firmware download and update

Note

•

No special server is necessary for the firmware update. You can use an HTTP or FTP server as the
firmware server by simply setting its URL.

•

You cannot use a TFTP server as the firmware server.

7.2 Firmware Update Settings

Firmware updates are provided by the manufacturer when necessary.
The firmware update will be executed by setting the corresponding parameters using configuration file
programming (

®

5.4.4 Firmware Update Settings

) or Web user interface programming (

®

see

4.8.1 Firmware Maintenance

). The following shows the parameters and the setting procedures:

Firmware Update Enable/Disable

•

In a configuration file, add the line,

FIRM_UPGRADE_ENABLE="Y"

.

•

In the Web user interface, click the

[Maintenance]

tab, click

[Firmware Maintenance]

, and then select

[Yes]

for

[Enable Firmware Update]

.

Firmware Version Number

•

In a configuration file, specify the new version number in "

FIRM_VERSION

".

Firmware Server URL

•

In a configuration file, specify the URL in "

FIRM_FILE_PATH

".

•

In the Web user interface, click the

[Maintenance]

tab, click

[Firmware Maintenance]

, and then enter the

URL in

[Firmware File URL]

.

220

Administrator Guide

Document Version 2012-07

Section 7 Firmware Update

«
...
218
219
220
221
222
...
»

Summary of Contents for KX-UT670



























































































































































































































































Reviews:

No comments

Related manuals for KX-UT670

Brand: Sagem Pages: 97

Brand: Sagem Pages: 99

Brand: Sagem Pages: 99

Brand: Sagem Pages: 89

Brand: Spice Pages: 54

Brand: InFocus Pages: 120

Brand: Yezz Pages: 68

Brand: Viking Pages: 2

Brand: WELLTECH Pages: 47

Brand: AOC Pages: 22

Brand: Sagem Pages: 61

Brand: PCD Pages: 16

Brand: Argos Pages: 23

Brand: Samsung Pages: 110

Brand: Samsung Pages: 84

Brand: Billow Pages: 131

Brand: Beko Pages: 18

Brand: Zte Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands