Panasonic KX-UT670 Administrator'S Manual Download Page 12

Page: 12 / 250

SIP_2NDPROXY_ADDR_n .......................................................................................194

SIP_2NDPROXY_PORT_n .......................................................................................194

SIP_2NDRGSTR_ADDR_n .......................................................................................194

SIP_2NDRGSTR_PORT_n .......................................................................................195

SIP_TIMER_T1_n .....................................................................................................195

SIP_TIMER_T2_n .....................................................................................................195

SIP_TIMER_T4_n .....................................................................................................196

SIP_FOVR_NORSP_n ..............................................................................................196

SIP_FOVR_MAX_n ...................................................................................................196

SIP_REFRESHER_n .................................................................................................197

SIP_DNSSRV_ENA_n ..............................................................................................197

SIP_UDP_SRV_PREFIX_n .......................................................................................197

SIP_TCP_SRV_PREFIX_n .......................................................................................198

SIP_100REL_ENABLE_n ..........................................................................................198

SIP_INVITE_EXPIRE_n ............................................................................................198

SIP_18X_RTX_INTVL_n ...........................................................................................199

SIP_PRSNC_ADDR_n ..............................................................................................199

SIP_PRSNC_PORT_n ..............................................................................................199

SIP_2NDPRSNC_ADDR_n .......................................................................................200

SIP_2NDPRSNC_PORT_n .......................................................................................200

USE_DEL_REG_OPEN_n ........................................................................................200

USE_DEL_REG_CLOSE_n ......................................................................................200

PORT_PUNCH_INTVL_n ..........................................................................................201

SIP_ADD_RPORT_n .................................................................................................201

SIP_REQURI_PORT_n .............................................................................................201

SIP_SUBS_EXPIRE_n ..............................................................................................202

SUB_RTX_INTVL_n ..................................................................................................202

REG_RTX_INTVL_n .................................................................................................203

SIP_P_PREFERRED_ID_n .......................................................................................203

SIP_PRIVACY_n .......................................................................................................203

ADD_USER_PHONE_n ............................................................................................203

SDP_USER_ID_n ......................................................................................................204

SUB_INTERVAL_RATE_n ........................................................................................204

SIP_OUTPROXY_ADDR_n ......................................................................................204

SIP_OUTPROXY_PORT_n .......................................................................................205

SIP_TRANSPORT_n .................................................................................................205

SIP_ANM_DISPNAME_n ..........................................................................................205

SIP_ANM_USERNAME_n ........................................................................................205

SIP_ANM_HOSTNAME_n ........................................................................................206

SIP_DETECT_SSAF_n .............................................................................................206

SIP_RCV_DET_HEADER_n .....................................................................................206

SIP_CONTACT_ON_ACK_n .....................................................................................207

SIP_TIMER_B_n .......................................................................................................207

SIP_TIMER_D_n .......................................................................................................207

SIP_TIMER_F_n .......................................................................................................208

SIP_TIMER_H_n .......................................................................................................208

SIP_TIMER_J_n ........................................................................................................208

ADD_TRANSPORT_UDP_n .....................................................................................208

ADD_EXPIRES_HEADER_n ....................................................................................209

SIP_HOLD_HOLDRECEIVE_n .................................................................................209

SIP_ADD_DIVERSION_n .........................................................................................209

SIP_RESPONSE_CODE_DND .................................................................................210

SIP_RESPONSE_CODE_CALL_REJECT ...............................................................210

6 Useful Telephone Functions ...............................................................211

Administrator Guide

Document Version 2012-07

Table of Contents

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands