Panasonic KX-UT670 Administrator'S Manual Download Page 98

Page: 98 / 250

4.6.3 VoIP Settings

This screen allows you to change the VoIP settings that are common to all lines.

4.6.3.1 RTP Settings

RTP Packet Time

Description

Selects the interval, in milliseconds, between transmissions of RTP
packets.

Value Range

•

30 (not available with the G.722 codec)

•

Default Value

Configuration File Reference

RTP_PTIME (Page 181)

Minimum RTP Port Number

Description

Specifies the lowest port number that the unit will use for RTP packets.

Note

•

If port numbers are specified in

[Channel 1–25]

4.4.5.3 External RTP Port

, this setting is ignored and the

corresponding external RTP port is enabled.

Administrator Guide

Document Version 2012-07

Section 4 Web User Interface Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands