Panasonic KX-UT670 Administrator'S Manual Download Page 170

Page: 170 / 250

RINGBACK_TONE_GAIN

Value Format

Integer

Description

Specifies the gain, in decibels, of the ringback tone.

Value Range

-24–6

Default Value

RINGBACK_TONE_TIMING

Value Format

Comma-separated Integer

Description

Specifies the pattern, in milliseconds, of ringback tones using up to 10
whole numbers (off 1, on 1, off 2, on 2…) separated by commas.

Note

•

It is recommended that you set a value of 60 milliseconds or
more for the first value (off 1).

Value Range

0–16000 (0: Infinite time)

Default Value

60,2000,3940

Web User Interface Reference

Tone Timings (Page 119)

HOLD_ALARM_FRQ

Value Format

Comma-separated Integer

Description

Specifies the dual-tone frequencies, in hertz, of the hold alarm using 2
whole numbers separated by a comma.

Value Range

0, 200–2000 (0: No tone)

Default Value

425

HOLD_ALARM_GAIN

Value Format

Integer

Description

Specifies the gain, in decibels, of the hold alarm.

Value Range

-24–6

Default Value

HOLD_ALARM_TIMING

Value Format

Comma-separated Integer

Description

Specifies the pattern, in milliseconds, of the hold alarm using up to 10
whole numbers (on 1, off 1, on 2, off 2…) separated by commas.

170

Administrator Guide

Document Version 2012-07

Section 5 Configuration File Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands