Panasonic KX-UT670 Administrator'S Manual Download Page 80

Page: 80 / 250

Default Value

STUN

Detection Interval

Description

Specifies the interval, in seconds, to wait between attempts to detect
the global IP address.

Value Range

0, 10–65535 (0: Disable)

Note

•

When

[Detection Method]

is set to

[SIP]

, the value "0" disables

detection and a value other than "0" enables detection.

Default Value

4.4.4.2 STUN Server

STUN Server Address

Description

Specifies the IP address or FQDN of the STUN server.

Value Range

Max. 127 characters

Default Value

Not stored.

Configuration File Reference

STUN_SERV_ADDR (Page 157)

STUN Server Port

Description

Specifies the port number of the STUN server.

Value Range

1–65535

Default Value

3478

Configuration File Reference

STUN_SERV_PORT (Page 158)

4.4.5 Static NAPT Settings

This screen allows you to configure the NAPT (Network Address Port Translation) settings. If the unit is
connected behind a router that uses NAT/NAPT to translate between private and global IP addresses, VoIP

Administrator Guide

Document Version 2012-07

Section 4 Web User Interface Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands