Panasonic KX-UT670 Administrator'S Manual Download Page 157

Page: 157 / 250

5.5.3 Time Adjust Settings

NTP_ADDR

Value Format

String

Description

Specifies the IP address or FQDN of the NTP server.

Note

•

If NTP settings are performed via the unit, this setting is
disabled.

Value Range

Max. 127 characters (IP address in dotted-decimal notation or FQDN)

Default Value

Empty string

TIME_SYNC_INTVL

Value Format

Integer

Description

Specifies the interval, in seconds, to resynchronize after having
detected no reply from the NTP server.

Note

•

If NTP settings are performed via the unit, this setting is
disabled.

Value Range

10–86400

Default Value

TIME_QUERY_INTVL

Value Format

Integer

Description

Specifies the interval, in seconds, between synchronizations with the
NTP server.

Note

•

If NTP settings are performed via the unit, this setting is
disabled.

Value Range

10–86400

Default Value

43200

5.5.4 STUN Settings

STUN_SERV_ADDR

Value Format

String

Description

Specifies the IP address or FQDN of the STUN server.

Document Version 2012-07

Administrator Guide

157

Section 5 Configuration File Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands