Panasonic KX-UT670 Administrator'S Manual Download Page 105

Page: 105 / 250

PCMU (Priority)

Description

Specifies the numerical order usage priority for the PCMU codec.

Value Range

1–255

Default Value

Configuration File Reference

CODEC_PRIORITYx_n (Page 177)

4.7 Telephone

This section provides detailed descriptions about all the settings classified under the

[Telephone]

tab.

4.7.1 Call Control

This screen allows you to configure various call features that are common to all lines.

4.7.1.1 Call Control

Send SUBSCRIBE to Voice Mail Server

Description

Selects whether to send the SUBSCRIBE request to a voice mail
server.

Note

•

Your phone system must support voice mail.

Value Range

•

Yes

•

Document Version 2012-07

Administrator Guide

105

Section 4 Web User Interface Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands