Panasonic KX-UT670 Administrator'S Manual Download Page 116

Page: 116 / 250

No Answer (Phone Number)

Description

Specifies the phone number of the destination to forward calls to when
a call is not answered after it has rung a specified number of times.

Note

•

If you change this setting when

[Synchronize Do Not Disturb

and Call Forward]

is set to

[Yes]

, the change to this setting is

not immediately applied on this screen. In this case, reload the
screen to confirm that the change is applied.

Value Range

Max. 32 characters

Note

•

You cannot leave this field empty if

[No Answer (Enable Call

Forward)]

is set to

[Yes]

Default Value

Not stored.

No Answer (Ring Count)

Description

Specifies the number of times that an incoming call rings until the call
is forwarded.

Note

•

If you change this setting when

[Synchronize Do Not Disturb

and Call Forward]

is set to

[Yes]

, the change to this setting is

not immediately applied on this screen. In this case, reload the
screen to confirm that the change is applied.

Value Range

0, 2–20 (0: No ring)

Default Value

116

Administrator Guide

Document Version 2012-07

Section 4 Web User Interface Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands