Panasonic KX-UT670 Administrator'S Manual Download Page 8

Page: 8 / 250

4.7.3.5

Reorder Tone ............................................................................................................120

Tone Frequencies ...................................................................................................120

Tone Timings ..........................................................................................................120

4.7.4

Telephone Settings ......................................................................................................120

4.7.4.1

Telephone Settings ....................................................................................................120

Number Matching Lower Digit .................................................................................120

Number Matching Upper Digit .................................................................................121

4.8

Maintenance ..................................................................................................................121

4.8.1

Firmware Maintenance .................................................................................................121

4.8.1.1

Firmware Maintenance ..............................................................................................121

Enable Firmware Update ........................................................................................121

Firmware File URL ..................................................................................................122

4.8.2

Provisioning Maintenance ............................................................................................122

4.8.2.1

Provisioning Maintenance .........................................................................................123

Enable Provisioning ................................................................................................123

Standard File URL ..................................................................................................123

Product File URL .....................................................................................................123

Master File URL ......................................................................................................124

Cyclic Auto Resync .................................................................................................124

Resync Interval .......................................................................................................124

Header Value for Resync Event .............................................................................124

4.8.3

Reset to Defaults ..........................................................................................................125

4.8.4

Restart ..........................................................................................................................125

4.9

Result Messages ...........................................................................................................126

5 Configuration File Programming ........................................................127

5.1

Configuration File Parameter List ...............................................................................128

5.2

General Information on the Configuration Files ........................................................135

5.2.1

Configuration File Specifications for Plain Text Provisioning .......................................135

5.2.2

Configuration File Parameters ......................................................................................136

5.2.3

Characters Available for String Values .........................................................................137

5.3

Configuration File Examples ........................................................................................137

5.3.1

Examples of Codec Settings ........................................................................................138

5.3.2

Example with Incorrect Descriptions ............................................................................138

5.4

System Settings ............................................................................................................140

5.4.1

Login Account Settings .................................................................................................140

ADMIN_ID .................................................................................................................140

ADMIN_PASS ...........................................................................................................140

USER_ID ...................................................................................................................140

USER_PASS .............................................................................................................140

5.4.2

System Time Settings ..................................................................................................141

TIME_ZONE_COUNTRY ..........................................................................................141

5.4.3

Syslog Settings .............................................................................................................143

SYSLOG_ADDR ........................................................................................................143

SYSLOG_PORT ........................................................................................................143

5.4.4

Firmware Update Settings ............................................................................................143

FIRM_UPGRADE_ENABLE ......................................................................................143

FIRM_VERSION ........................................................................................................143

FIRM_FILE_PATH .....................................................................................................144

5.4.5

Provisioning Settings ....................................................................................................144

OPTION66_ENABLE .................................................................................................144

PROVISION_ENABLE ..............................................................................................145

CFG_STANDARD_FILE_PATH ................................................................................145

CFG_PRODUCT_FILE_PATH ..................................................................................146

CFG_MASTER_FILE_PATH .....................................................................................147

Administrator Guide

Document Version 2012-07

Table of Contents

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands