Panasonic KX-UT670 Administrator'S Manual Download Page 120

Page: 120 / 250

4.7.3.5 Reorder Tone

Tone Frequencies

Description

Specifies the dual-tone frequencies, in hertz, of reorder tones using 2
whole numbers separated by a comma.

Value Range

0, 200–2000 (0: No tone)

Default Value

480,620

Configuration File Reference

REORDER_TONE_FRQ (Page 169)

Tone Timings

Description

Specifies the pattern, in milliseconds, of reorder tones using up to 10
whole numbers (off 1, on 1, off 2, on 2…) separated by commas.

Note

•

It is recommended that you set a value of 60 milliseconds or
more for the first value (off 1).

Value Range

0–16000 (0: Infinite time)

Default Value

60,250,190

Configuration File Reference

REORDER_TONE_TIMING (Page 169)

4.7.4 Telephone Settings

This screen allows you to configure various telephone settings.

4.7.4.1 Telephone Settings

Number Matching Lower Digit

Description

Specifies the minimum number of digits with which to match a
phonebook entry with an incoming call’s caller ID. To specify exact
matching of entire numbers only, specify "0".

120

Administrator Guide

Document Version 2012-07

Section 4 Web User Interface Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands