Panasonic KX-UT670 Administrator'S Manual Download Page 171

Page: 171 / 250

Value Range

0–16000 (0: Infinite time)

Default Value

120,14880

CW_TONE1_FRQ

Value Format

Comma-separated Integer

Description

Specifies the dual-tone frequencies, in hertz, of call waiting tone 1 using
2 whole numbers separated by a comma.

Value Range

0, 200–2000 (0: No tone)

Default Value

425

CW_TONE1_GAIN

Value Format

Integer

Description

Specifies the gain, in decibels, of call waiting tone 1.

Value Range

-24–6

Default Value

CW_TONE1_TIMING

Value Format

Comma-separated Integer

Description

Specifies the pattern, in milliseconds, of call waiting tone 1 using up to
10 whole numbers (on 1, off 1, on 2, off 2…) separated by commas.

Value Range

0–16000 (0: Infinite time)

Default Value

120,120,120,120,120,14400

HOLD_TONE_FRQ

Value Format

Comma-separated Integer

Description

Specifies the dual-tone frequencies, in hertz, of the hold tone using 2
whole numbers separated by a comma.

Value Range

0, 200–2000 (0: No tone)

Default Value

425

HOLD_TONE_GAIN

Value Format

Integer

Description

Specifies the gain, in decibels, of the hold tone.

Document Version 2012-07

Administrator Guide

171

Section 5 Configuration File Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands