Panasonic KX-UT670 Administrator'S Manual Download Page 167

Page: 167 / 250

DIAL_TONE2_GAIN

Value Format

Integer

Description

Specifies the gain, in decibels, of Dial Tone 2.

Value Range

-24–6

Default Value

DIAL_TONE2_TIMING

Value Format

Comma-separated Integer

Description

Specifies the pattern, in milliseconds, of Dial Tone 2 using up to 10
whole numbers (off 1, on 1, off 2, on 2…) separated by commas.

Note

•

It is recommended that you set a value of 60 milliseconds or
more for the first value (off 1).

Value Range

0–16000 (0: Infinite time)

Default Value

60,0

DIAL_TONE4_FRQ

Value Format

Comma-separated Integer

Description

Specifies the dual-tone frequencies, in hertz, of Dial Tone 4 (stutter dial
tones) to notify that a voice mail is waiting, using 4 whole numbers
separated by a comma.

Value Range

0, 200–2000 (0: No tone)

Default Value

350,440

Web User Interface Reference

Tone Frequencies (Page 119)

DIAL_TONE4_GAIN

Value Format

Integer

Description

Specifies the gain, in decibels, of Dial Tone 4 (stutter-type dial tone).

Value Range

-24–6

Default Value

DIAL_TONE4_TIMING

Value Format

Comma-separated Integer

Document Version 2012-07

Administrator Guide

167

Section 5 Configuration File Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands