Panasonic EBL512 Operating Instructions Manual Download Page 92

Page: 92 / 172

Panasonic Eco Solutions Nordic AB

MEW01457

Rev: -

Operating Instructions Fire alarm system EBL512, V2.7.x

This text message means that the SSD have not been downloaded. A
new download has to be performed.

22.1

Boot menu

The Boot menu should be used by

authorised personnel only

NOTE!

Vital data can be erased via this menu.

The Boot menu is opened as follows:

Perform a reset / restart:



Power off / power on
or



Jumper JP4 on the main board

The following text messages will be show in the LCD:

Checking program memory......

And after that:

Booting......

When the text "Booting……" appears, press

"Access"

and 0.1 sec.

later also press

"1"

and the

Boot menu

will be shown:

1:Reset, 2:Clear mem, 4:Read AD, 5:MSClo
ck, 6:Checksum, 7:Cursor, 8:Texts

Press

"1"

to perform a reset / restart (you will also leave the Boot

menu).
Press

"2"

to open the Clear memory menu, see below.

The alternatives 3-8 are for R & D use only!!

The

Clear memory menu

1 = SSD, 2 = SSW, 3 = SysInfo, 4 = Echel
oninfo, 5 = Texts

Press

"1"

to clear the SSD memory.

Press

"2"

to clear the SSW memory.

The alternatives 3-5 are for R & D use only!!

"Erasing SSD" and "Erasing SSW" respectively will be shown and
then the Clear memory menu will be shown again.

Press

"Return"

to go back to the Boot menu.

Can also be done in Win512, EBL512 settings dialog box, "Clear SSD".

Summary of Contents for EBL512













































































































































































Search results

Summary of Contents for EBL512

Reviews:

Brands by name

Popular brands

Panasonic EBL512, Operating Instructions Manual

Search results

Summary of Contents for EBL512

Reviews:

Brands by name

Popular brands