Panasonic EBL512 Operating Instructions Manual Download Page 115

Page: 115 / 172

Panasonic Eco Solutions Nordic AB

MEW01457

Rev: -

Operating Instructions Fire alarm system EBL512, V2.7.x

113

27.4

Activated 2-zone/address dependent
zone/address (H4/U4)

(

"Two unit dependent"

in Win512): When only one

zone

or one

zone / address

(alarm point) is in alarm status

, the buzzer (in the

c.i.e.) sounds (0.8 / 5 sec.) and there is a

Co-incidence alarm

presentation in the c.i.e. display.

The unit(s) or zone(s) in Co-incidence alarm status is (are) shown in
this menu, from which it is also possible to get a print-out.

Action

Text in display

Comments

Co-incidence alarm detector ZZZ/AA
User definable text message (if progr.)
or
Co-incidence alarm zone ZZZ
User definable text message (if progr.)

One alarm point or zone

has activated a Co-

incidence alarm.

ZZZ = zone number

AA = address

"Access"

According to chapter

"Access", see page 92.

Scroll to menu H4.

Present system status on display and
printer ACCEPT? H4

"A"

Disablement
Printout: (1=yes) U1

Scroll to menu U4.

Activated 2-zone/address dependent
zone/address Printout: (1=yes) U4

Press "1" for an automatic

print-out.

Press "A" for presentation

in the display.

"A"

When "A" is pressed, the active zone & address (or zone)

will be shown in the display, e.g:

Co-incidence alarm detector ZZZ/AA

L
or

Co-incidence alarm zone ZZZ

This is a list in which you

can scroll. If there are no

"alarms" and if "Return" is

pressed, menu U4 will be

shown again.

"1"

Printing started. To stop printing press
C and 0 simultaneously ACCEPT?

Press "A" and menu U4

will be shown again.

"Return"

Activated 2-zone/address dependent
zone/address Printout: (1=yes) U4

Scroll or press "Return" to

menu H4. Scroll or press

"Return" to log off.

When two or more

zones

units

(zone / addresses), dependent on each

other, are in alarm status at the same time, normal fire alarm will be activated

in the system.

Summary of Contents for EBL512













































































































































































Search results

Summary of Contents for EBL512

Reviews:

Brands by name

Popular brands

Panasonic EBL512, Operating Instructions Manual

Search results

Summary of Contents for EBL512

Reviews:

Brands by name

Popular brands