Panasonic EBL512 Operating Instructions Manual Download Page 124

Page: 124 / 172

Panasonic Eco Solutions Nordic AB

MEW01457

Rev: -

Operating Instructions Fire alarm system EBL512, V2.7.x

122

27.6

Sensors activating SERVICE signal (H4/U6)

Service signal is indicated by LED "Service" (L12). The sensor week
average value is below or over the service level respectively for one or
more sensors. (Regarding the service signal levels, see Planning
Instructions, chapter "Service signal".

Menu H4/U6 is a list of the sensor(s) activating service signal.

NOTE!

Service signal is only information that the sensors have to be

cleaned / replaced soon. The service signal has to be acknowledged,
see chapter "Acknowledge SERVICE signal (H8/S4)", page 145.

It is not possible to get a print-out from menu H4/U6.

Action

Text in display

Comments

"Access"

According to chapter

"Access", see page 92.

Scroll to menu H4.

Present system status on display and
printer ACCEPT? H4

"A"

Disablement
Printout: (1=yes) U1

Scroll to menu U6.

Sensors activating SERVICE signal
U6

Press "A" to accept.

"A"

Sensor : xxxxxx needs service
L

L = a list in which you

can scroll. Press "Return"

to menu U6. (If there are

no sensors in the list,

menu U6 will be shown

again.).

"Return"

Sensors activating SERVICE signal
U6

Scroll or press "Return"

to menu H4. Scroll or

press "Return" to log off.

Summary of Contents for EBL512













































































































































































Search results

Summary of Contents for EBL512

Reviews:

Related manuals for EBL512

Brands by name

Popular brands

Panasonic EBL512, Operating Instructions Manual

Search results

Summary of Contents for EBL512

Reviews:

Related manuals for EBL512

Brands by name

Popular brands