Panasonic AG-RCP30P Operating Instructions Manual Download Page 55

Page: 55 / 64

Error Messages

No.

Message

Measure

E02431 DSP error. Reproduction and

record cannot be performed.

Wait until the error message is cleared.

Call your supplier if the message does

not clear after about a minute.

E02432

E02440 System error

Couldn’t format P2 cards.

Insert another P2 card.

E02441 Couldn’t format P2 cards.
E02442 Found read only P2 cards.

Couldn’t format.

Disable P2 card write-protection.

E02443 Not P2 card.

Couldn’t format.

The inserted card is not a P2 card.

Replace the card with a P2 card.

E02444 No card.

Couldn’t format.

Insert a P2 card.

E02460 System error

Couldn’t delete files.

Contact your supplier.

E02461 Couldn’t delete files.
E02470 System error

Couldn’t restore files.

E02471 Couldn’t restore files.
E02481 Write error on slot1.

Record cannot be continued.

Be sure to use the correct procedure

to remove and load P2 cards. Replace

a P2 card that is not recognized after

inserting it in the P2 card slot and

closing the P2 card slot cover.

E02482 Write error on slot2.

Record cannot be continued.

E07671 Camera communication error.

Camera cannot be controlled.

The Color Camera may not be correctly

connected. Check whether the camera

cable (included in the Color Camera)

is correctly connected to the Color

Camera. Call your supplier if this

measure does not solve the problem.

E08601 Lid open.

Reproduction and record

cannot be performed.

Close the P2 card slot cover.

E08602 The recorder’s fan has

stopped.

Contact your supplier.

E10400 Radar model file not found.
E10401 More than five radar model

files found.

E10402 Invalid radar model file

found.

E10403 Radar model file read error.
E10410 Radar communication error.

Please check the radar

setting.

Summary of Contents for AG-RCP30P
































































Search results

Summary of Contents for AG-RCP30P

Reviews:

Related manuals for AG-RCP30P

Brands by name

Popular brands

Panasonic AG-RCP30P, Operating Instructions Manual

Search results

Summary of Contents for AG-RCP30P

Reviews:

Related manuals for AG-RCP30P

Brands by name

Popular brands