Outdoor living today 8x15 SpaceMaker Garden Shed Assembly Manual Download | Manualshive

Page: 21 / 31

background image

Roof Batten flush
with rafter end.

49.

Place Roof Panel so it sits flush on 3rd rafter from the outside (doubled up rafter). Lowest batten on

roof should be flush with end of rafter at bottom. From the outside, screw down through bottom row of
shingles into rafter with 1 - 2 1/2” screw.

50.

Locate 2 Mid Roof Panels (roof battens flush to with shingles) and Front Outside Roof Panel

(shingles overhang battens). Place on rafters and align panels as per

Step 49.

Screw Mid Panels

down to rafters with 2 - 2 1/2” screws in the bottom row of shingles. Attach Front as per

Step 49.

51.

Position and attach remaining Roof Panels as per

Steps 49-50.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 21

«
...
19
20
21
22
23
...
»

Summary of Contents for 8x15 SpaceMaker Garden Shed
































Reviews:

No comments

Related manuals for 8x15 SpaceMaker Garden Shed

Brand: Bear County Pages: 17

Brand: Palmako Pages: 19

Annabel EL18-4533-4

Brand: Palmako Pages: 45

Brand: USP Pages: 61

Brand: Rutland County Pages: 5

Tomas FR34-3857

Brand: Palmako Pages: 115

Brand: OLT Pages: 36

SunShed Greenhouse 8x12

Brand: OLT Pages: 38

Brand: Palmako Pages: 25

MIKKEL EL16-1811

Brand: Palmako Pages: 67

OLAF ELT18-4633

Brand: Palmako Pages: 31

Brand: Palmako Pages: 72

Brand: Backyard Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands