Outdoor living today 8x15 SpaceMaker Garden Shed Assembly Manual Download | Manualshive

Page: 13 / 31

background image

29.

Lift up a completed gable section and place on top of Rear Top Plate on wall. The rear gable

framing should sit flush with the inside of the top plate.

30.

The gable should be centered sideways (left to right) on the top plate.

Hint:

use a straight

edge to check the angle of the gable framing and top plate. Both angles should line up. Adjust
gable accordingly. When positioned correctly, attach to walls and top plate with 8 - 2” screws. Screw
from the bottom of gable framing down into Top Plate and Wall.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 13

Note-

Prior to attaching, check from

front (siding side) to confirm siding lines up
reasonably well. Try each combination
prior to attaching together to get the best
fit.

straight edge

Gable Framing

«
...
11
12
13
14
15
...
»

Summary of Contents for 8x15 SpaceMaker Garden Shed
































Reviews:

No comments

Related manuals for 8x15 SpaceMaker Garden Shed

Brand: Palmako Pages: 59

Overlap Apex Shed

Brand: Forest garden Pages: 2

Brand: Duratuf Pages: 43

Brand: Palmako Pages: 38

Brand: GARDEN MASTER Pages: 2

Brand: GARDEN MASTER Pages: 2

DUOTECH OAKLAND 754

Brand: Keter Pages: 52

Brand: Solid Build Pages: 24

Brand: Palmako Pages: 63

12x12 Space Maker Garden Shed with Plywood Roof & AK...

Brand: OLT Pages: 42

Brand: Palmako Pages: 59

Brand: habitat et jardin Pages: 29

Brand: habitat et jardin Pages: 12

Active Fun TP349

Brand: TP Toys Pages: 16

Brand: Palmako Pages: 62

Brand: Palmako Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands