manualshive.com logo in svg

Outdoor living today 8x15 SpaceMaker Garden Shed, Assembly Manual

Share
Download
Outdoor living today 8x15 SpaceMaker Garden Shed Assembly Manual Download Page 22

53.

Screw first Filler Shingle down to

rafters using 1 - 2.5” screw per panel.
Make sure to screw into rafter.

54.

Slide in another Filler Shingle and attach

as per 

Step 53.

On your last row of shingles,

the Filler Shingle is precut to fit properly.  Attach
to roof with 2 - 1 1/2” Shingle nails per shingle.

Attach above the
exposure line.

Exposure Line

52. 

Roof 

Filler Shingles

are included to

cover roof seams. Starting at the bottom,
slide the first Long Shingle in until flush
with other bottom shingles.

DO NOT

ATTACH UNTIL STEP 53. 

55. 

To further secure roof panels, from the inside, locate pre-drilled holes in Mid Rafters (3 per Rafter).

Using 2 - 4” screws, secure rafters to roof battens. 

Note,

from outside, push roof panel down so batten

sit flush against rafter when securing. Also position 2 Simpson Strong ties on battens and outside rafters
and secure 4 - 1 1/4” screws. 8 ties in total.  

4” screws 

4- 90 degree Simpson
Ties / Gable.

Toll Free 1-888-658-1658             www.outdoorlivingtoday.com          [email protected]

Page 22

Summary of Contents for 8x15 SpaceMaker Garden Shed
































Reviews:

No comments

Brands by name

Popular brands

Load more brands