Outdoor living today 8x15 SpaceMaker Garden Shed Assembly Manual Download

Page: 3 / 31

A. Floor Section

Plywood Floor
Large (4)

Floor Joist
Frames
Large (4)

Floor Runners (15)

Plywood Floor
Small (4)

Exploded view of all parts necessary to complete
Floor Section. Identify all parts prior to starting.

Note, Floor Footprint is 182” deep x 96” wide.

Concrete Pad
(optional foundation method)

Floor Joist
Frames
Small (4)

Lay out

Large Floor Joist Frame and 2 Floor Joists

as illustrated above. Position Joists

equally in Floor Joist Frame. Use

Small Floor Joist Frame

as a template to determine joist position.

Position Joist so flush with framing.

Flush
with
framing

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 3

Summary of Contents for 8x15 SpaceMaker Garden Shed
































Search results

Summary of Contents for 8x15 SpaceMaker Garden Shed

Reviews:

Related manuals for 8x15 SpaceMaker Garden Shed

Brands by name

Popular brands

Outdoor living today 8x15 SpaceMaker Garden Shed, Assembly Manual

Search results

Summary of Contents for 8x15 SpaceMaker Garden Shed

Reviews:

Related manuals for 8x15 SpaceMaker Garden Shed

Brands by name

Popular brands