Outdoor living today 8x15 SpaceMaker Garden Shed Assembly Manual Download | Manualshive

Page: 19 / 31

background image

45.

With both Rafter Ridge Boards

connected. Completely secure
Gable framing to both outside rafters
with 8 - 2” screws per gable side.

Metal Offsetting
Ridge Board
Connectors

44.

At the peak, align Ridge Boards so

they are flush together and secure them with
16 - 1 1/4” screws.

Important

- if there is a

gap between Ridge Boards, try pushing side
walls closer together from outside. Walls
should be 91” apart at top from inside of wall
plate to wall plate.
To completely secure Ridge Boards, place
4 - 1 1/4” screws into any of the remaining
Metal Ridge Board Connectors holes.
Complete both sides. (2 per side)

43.

Remove temporary Filler Trims required to help support Rafter Sections.

Important-

Do not discard, will need later.

Remove temporary
Filler Trim.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 19

«
...
17
18
19
20
21
...
»

Summary of Contents for 8x15 SpaceMaker Garden Shed
































Reviews:

No comments

Related manuals for 8x15 SpaceMaker Garden Shed

Brand: Palmako Pages: 63

Brand: Duratuf Pages: 43

Brand: Palmako Pages: 48

Brand: Gartenpro Pages: 41

Brand: Palmako Pages: 55

Brand: Palmako Pages: 20

Santa Rosa SR812-FJ-Cedar

Brand: OLT Pages: 54

Santa Rosa SR812-FJ-Metal

Brand: OLT Pages: 56

Brand: Palmako Pages: 62

Brand: Palmako Pages: 61

Brand: Palmako Pages: 99

Sunbrella Side Shade

Brand: Pergola kits USA Pages: 10

Brand: Palmako Pages: 54

Whitewood Malta 2

Brand: Palmako Pages: 20

Brand: Palmako Pages: 58

Brand: Palmako Pages: 48

Brand: Solid Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands