Outdoor living today 8x15 SpaceMaker Garden Shed Assembly Manual Download | Manualshive

Page: 17 / 31

background image

37.

Flip Rafter Section over so Soffit is

facing down.

36.

To fortify the completed Rafter

Section prior to lifting on to roof,
temporarily secure 2 - 75” long Filler
Trim pieces to rafters as shown to the
left with 4 - 1 1/4” screws per pieces.

Important-

Do not discard Filler Trim

Pieces, will need later.

38.

With several helpers, lift

completed Rafter Section up above
the walls.

39.

Carefully slide outside

rafters of Rafter Section up
on gable framing.

Temporarily attach 2 Filler
Trim Pieces to secure Rafter
Section while lifting. (Filler
Trims found in

Step 57.

Soffit

Gable Framing

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 17

«
...
15
16
17
18
19
...
»

Summary of Contents for 8x15 SpaceMaker Garden Shed
































Reviews:

No comments

Related manuals for 8x15 SpaceMaker Garden Shed

Brand: Palmako Pages: 72

FRB28-2923-5FSC

Brand: Palmako Pages: 33

Brand: Palmako Pages: 45

Brand: Palmako Pages: 54

Brand: Lemeks Pages: 71

Palmako FRF28-3829

Brand: Lemeks Pages: 62

Palmako FRBC44-5540

Brand: Lemeks Pages: 63

Palmako FRB28-3232-3

Brand: Lemeks Pages: 52

Palmako Ella FRB28-2632

Brand: Lemeks Pages: 92

PALMAKO ANDRE EL18-4555-3

Brand: Lemeks Pages: 60

Brand: Lemeks Pages: 154

Brand: G21 Pages: 52

Brand: Mercia Garden Products Pages: 10

Brand: Palmako Pages: 36

Brand: Palmako Pages: 53

12x12 SpaceMaker Garden Shed

Brand: OLT Pages: 46

Brand: Palmako Pages: 76

Brand: habitat et jardin Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands