manualshive.com logo in svg

Outdoor living today 8x15 SpaceMaker Garden Shed, Assembly Manual

Share
Download
Outdoor living today 8x15 SpaceMaker Garden Shed Assembly Manual Download Page 7

14.

Starting at Rear Corner, position a  Wall Panel on

top of plywood floor. Depending on your preference, you
may use a solid or window wall panel in this position. If
using a solid wall, make sure panel is facing up.  

Important:

Make sure all walls are aligned in their
upright position. If not ,water may leak into
your shed. Unsure if panel is facing up or
down?  check siding on window wall panel
to match alignment.

15.

The side wall panels will sit flush at the end

of the plywood floor with the front and rear panels 
sandwiching between them. 

Note:

Siding will overhang the floor by approx.

1/2” 

Outside 2x3 Plate of wall panel is
flush with outside of plywood
when properly aligned.

Side Wall Panel

Rear

of Shed

Bottom Wall Plate

13. 

Starting with 

Solid Wall Panels

, carefully lay panel face down. Position and attach 

Wall

Plate

to bottom of wall studs of each wall panel with 6 - 2 1/2” screws. Position so plates are flush

with framing. 

Toll Free 1-888-658-1658             www.outdoorlivingtoday.com          [email protected]

Page 7

Summary of Contents for 8x15 SpaceMaker Garden Shed
































Reviews:

No comments

Brands by name

Popular brands

Load more brands