manualshive.com logo in svg

OTE Speedport Entry 2i, Maintenance Management Manual

Share
Download
OTE Speedport Entry 2i Maintenance Management Manual Download Page 4

SJ-20162405182123-002|2016-05-24 (R2.0) 

 

 

 

 

4 

 

 

 

 

3.11. Configure the Multicast ........................................................................................................ 3-34

 

3.11.1. Configure the IGMP ................................................................................................... 3-34

 

3.11.2. Configure the MLD .................................................................................................... 3-35

 

Chapter 4. Configure the Local  Network..............................................................4-1

 

4.1. Check the Local Network  Status ............................................................................................... 4-1

 

4.2. Configure the WLAN ................................................................................................................. 4-2

 

4.2.1. Configure the Basic Parameters of the WLAN ............................................................... 4-2

 

4.2.2. Configure the Advanced Parameters of the WLAN ....................................................... 4-5

 

4.3. Configure the LAN ..................................................................................................................... 4-7

 

4.3.1. Configure the LAN (IPv4) ............................................................................................... 4-7

 

4.3.2. Configure the LAN (IPv6) ............................................................................................. 4-10

 

4.4. Configure Route Menu ............................................................................................................ 4-14

 

4.4.1. Configure Routing (IPv4) .............................................................................................. 4-14

 

4.4.2. Configure Routing (IPv6) .............................................................................................. 4-17

 

4.5. Configure the UPnP ................................................................................................................. 4-20

 

Chapter 5. Configure the  VoIP .............................................................................5-1

 

5.1. Configure the SIP Accounts ....................................................................................................... 5-1

 

5.2. Configure the Binding of VoIP  port............................................................................................ 5-3

 

Chapter 6. Configure the  Management and  Diagnosis .......................................6-1

 

6.1. Check the Device  Status ............................................................................................................ 6-1

 

6.2. Configure the Account Management ........................................................................................ 6-2

 

6.3. Configure the Login  Timeout .................................................................................................... 6-2

 

6.4. Configure the System Management ......................................................................................... 6-3

 

6.4.1. Configure the Device Management............................................................................... 6-3

 

6.4.2. Upgrade Software .......................................................................................................... 6-4

 

6.4.3. Manage the User Configuration .................................................................................... 6-5

 

6.5. Check the  TR-069 ...................................................................................................................... 6-5

 

6.6. Manage the Log ........................................................................................................................ 6-7

 

6.7. Diagnosis ................................................................................................................................... 6-8

 

6.8. Trace Route Diagnosis ............................................................................................................... 6-9

 

6.9. Check the ARP  Table ................................................................................................................ 6-12

 

6.10. Check the MAC  Table ............................................................................................................ 6-13

 

6.11. Configure the Telephone Compatibility ................................................................................. 6-13

 

Abbreviations ......................................................................................................... I 
Figures ...................................................................................................................4

 

Tables .....................................................................................................................8

 

 

Summary of Contents for Speedport Entry 2i




































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands