manualshive.com logo in svg

OTE Speedport Entry 2i, Maintenance Management Manual

Share
Download
OTE Speedport Entry 2i Maintenance Management Manual Download Page 80

SJ-20162405182123-002|2016-05-24 (R2.0) 

 

 

 

Speedport Entry 2i Maintenance Management Guide  

 

 

6-4

 

 

 

 

 

 

2.  On this page, you can perform the following  operations: 

l  Click 

Reboot 

to reboot the Speedport Entry 2i device. 

l  Click 

Factory Reset 

to restore the factory default settings. 

– End of Steps  – 

 

6.4.2.

 

Upgrade Software 

This procedure introduces how to upgrade Software. 

 

Prerequisite 

Before upgrading software, make sure that the upgrade file is ready. 

 

Steps 

1.  On the main page of the Speedport Entry 2i, select 

Management >  System 

Management > Software Upgrade 

to go to the 

Software Upgrade 

page. 

The page is shown in 

Figure  6-5

. 

 

Figure 6-5 Software Upgrading Page

 

 

 

 

2.  Click 

Browse 

to select the upgrade version  file. 

3.  Click 

Upgrade

. 

 

 

 

 

The system prompts the upgrade progress. During the upgrade, do not  cut  off the 

power supply.  Otherwise, the device may be damaged. 

Generally,  the  software  is  upgraded  by  the  Remote Management Server.  If 

the user wants to upgrade the Firmware locally, obtain the latest Firmware  version 

from 

www.cosmote.gr

 website. 

 

 

 

– End of Steps  – 

 

Note: 

Summary of Contents for Speedport Entry 2i




































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands